CLIA Kit for Phosphoserine Phosphatase (PSPH)

PSP; L-3-phosphoserine phosphatase; O-phosphoserine phosphohydrolase

  • CLIA Kit for Phosphoserine Phosphatase (PSPH) Packages (Simulation)
  • CLIA Kit for Phosphoserine Phosphatase (PSPH) Packages (Simulation)
  • CLIA Kit for Phosphoserine Phosphatase (PSPH) Results demonstration
  • SCC736Hu.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Phosphoserine Phosphatase (PSPH)

This assay has high sensitivity and excellent specificity for detection of Phosphoserine Phosphatase (PSPH).
No significant cross-reactivity or interference between Phosphoserine Phosphatase (PSPH) and analogues was observed.

Precision of the CLIA Kit for Phosphoserine Phosphatase (PSPH)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Phosphoserine Phosphatase (PSPH) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Phosphoserine Phosphatase (PSPH) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for Phosphoserine Phosphatase (PSPH)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Phosphoserine Phosphatase (PSPH)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Phosphoserine Phosphatase (PSPH)

The microplate provided in this kit has been pre-coated with an antibody specific to Phosphoserine Phosphatase (PSPH). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Phosphoserine Phosphatase (PSPH). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Phosphoserine Phosphatase (PSPH) level in the sample or standard.;

Related products

Catalog No. Organism species: Homo sapiens (Human) Applications (RESEARCH USE ONLY!)
RPC736Hu01 Recombinant Phosphoserine Phosphatase (PSPH) Positive Control; Immunogen; SDS-PAGE; WB.
PAC736Hu01 Polyclonal Antibody to Phosphoserine Phosphatase (PSPH) WB; IHC; ICC; IP.
MAC736Hu21 Monoclonal Antibody to Phosphoserine Phosphatase (PSPH) WB; IHC; ICC; IP.
SCC736Hu CLIA Kit for Phosphoserine Phosphatase (PSPH) Chemiluminescent immunoassay for Antigen Detection.
GUESTBOOK