CLIA Kit for Lactoperoxidase (LPO)

SPO; Salivary peroxidase

  • CLIA Kit for Lactoperoxidase (LPO) Packages (Simulation)
  • CLIA Kit for Lactoperoxidase (LPO) Packages (Simulation)
  • CLIA Kit for Lactoperoxidase (LPO) Results demonstration
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Lactoperoxidase (LPO)

This assay has high sensitivity and excellent specificity for detection of Lactoperoxidase (LPO).
No significant cross-reactivity or interference between Lactoperoxidase (LPO) and analogues was observed.

Precision of the CLIA Kit for Lactoperoxidase (LPO)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Lactoperoxidase (LPO) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Lactoperoxidase (LPO) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for Lactoperoxidase (LPO)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Lactoperoxidase (LPO)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Lactoperoxidase (LPO)

The microplate provided in this kit has been pre-coated with an antibody specific to Lactoperoxidase (LPO). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Lactoperoxidase (LPO). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Lactoperoxidase (LPO) level in the sample or standard.;

Related products

Catalog No. Organism species: Bos taurus; Bovine (Cattle) Applications (RESEARCH USE ONLY!)
RPA296Bo01 Recombinant Lactoperoxidase (LPO) Positive Control; Immunogen; SDS-PAGE; WB.
PAA296Bo01 Polyclonal Antibody to Lactoperoxidase (LPO) WB; IHC; ICC; IP.
MAA296Bo21 Monoclonal Antibody to Lactoperoxidase (LPO) WB; IHC; ICC; IP.
SEA296Bo ELISA Kit for Lactoperoxidase (LPO) Enzyme-linked immunosorbent assay for Antigen Detection.
SCA296Bo CLIA Kit for Lactoperoxidase (LPO) Chemiluminescent immunoassay for Antigen Detection.
LMA296Bo Multiplex Assay Kit for Lactoperoxidase (LPO) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK