CLIA Kit for High Temperature Requirement Factor A4 (HTRA4)

HtrA Serine Peptidase 4

  • CLIA Kit for High Temperature Requirement Factor A4 (HTRA4) Packages (Simulation)
  • CLIA Kit for High Temperature Requirement Factor A4 (HTRA4) Packages (Simulation)
  • CLIA Kit for High Temperature Requirement Factor A4 (HTRA4) Results demonstration
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for High Temperature Requirement Factor A4 (HTRA4)

This assay has high sensitivity and excellent specificity for detection of High Temperature Requirement Factor A4 (HTRA4).
No significant cross-reactivity or interference between High Temperature Requirement Factor A4 (HTRA4) and analogues was observed.

Recovery of the CLIA Kit for High Temperature Requirement Factor A4 (HTRA4)

Matrices listed below were spiked with certain level of recombinant High Temperature Requirement Factor A4 (HTRA4) and the recovery rates were calculated by comparing the measured value to the expected amount of High Temperature Requirement Factor A4 (HTRA4) in samples.

Matrix Recovery range (%) Average(%)
serum(n=5) 80-98 90
EDTA plasma(n=5) 79-103 99
heparin plasma(n=5) 82-93 88

Precision of the CLIA Kit for High Temperature Requirement Factor A4 (HTRA4)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level High Temperature Requirement Factor A4 (HTRA4) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level High Temperature Requirement Factor A4 (HTRA4) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Linearity of the CLIA Kit for High Temperature Requirement Factor A4 (HTRA4)

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of High Temperature Requirement Factor A4 (HTRA4) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
serum(n=5) 90-105% 81-88% 89-103% 90-105%
EDTA plasma(n=5) 88-95% 94-105% 78-91% 80-91%
heparin plasma(n=5) 79-95% 88-95% 80-91% 78-90%

Stability of the CLIA Kit for High Temperature Requirement Factor A4 (HTRA4)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for High Temperature Requirement Factor A4 (HTRA4)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for High Temperature Requirement Factor A4 (HTRA4)

The microplate provided in this kit has been pre-coated with an antibody specific to High Temperature Requirement Factor A4 (HTRA4). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to High Temperature Requirement Factor A4 (HTRA4). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the High Temperature Requirement Factor A4 (HTRA4) level in the sample or standard.;

Related products

Catalog No. Organism species: Homo sapiens (Human) Applications (RESEARCH USE ONLY!)
RPN048Hu01 Recombinant High Temperature Requirement Factor A4 (HTRA4) Positive Control; Immunogen; SDS-PAGE; WB.
PAN048Hu01 Polyclonal Antibody to High Temperature Requirement Factor A4 (HTRA4) WB; IHC; ICC; IP.
MAN048Hu21 Monoclonal Antibody to High Temperature Requirement Factor A4 (HTRA4) WB; IHC; ICC; IP.
SEN048Hu ELISA Kit for High Temperature Requirement Factor A4 (HTRA4) Enzyme-linked immunosorbent assay for Antigen Detection.
SCN048Hu CLIA Kit for High Temperature Requirement Factor A4 (HTRA4) Chemiluminescent immunoassay for Antigen Detection.
LMN048Hu Multiplex Assay Kit for High Temperature Requirement Factor A4 (HTRA4) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK