CLIA Kit for Complement Component 5a (C5a)
- Product No.SCA388Ra
- Organism SpeciesRattus norvegicus (Rat) Same name, Different species.
- Test MethodDouble-antibody Sandwich
- Assay Length2h, 40min
- Detection Range0.27-200ng/mL
- SensitivityThe minimum detectable dose of this kit is typically less than 0.11ng/mL.
- Sample Typeserum, plasma and other biological fluids
- Download Instruction Manual
- UOM 48T96T 96T*5 96T*10 96T*100
-
FOB
US$ 638
For more details, please contact local distributors!US$ 912
For more details, please contact local distributors! US$ 4104
For more details, please contact local distributors! US$ 7752
For more details, please contact local distributors! US$ 63840
For more details, please contact local distributors!
-
Packages (Simulation)
-
Packages (Simulation)
-
Results demonstration
-
Typical Standard Curve
-
ISO9001: 2008, ISO13485: 2003 Registered
Specificity of the CLIA Kit for Complement Component 5a (C5a)
This assay has high sensitivity and excellent specificity for detection of Complement Component 5a (C5a).
No significant cross-reactivity or interference between Complement Component 5a (C5a) and analogues was observed.
Recovery of the CLIA Kit for Complement Component 5a (C5a)
Matrices listed below were spiked with certain level of recombinant Complement Component 5a (C5a) and the recovery rates were calculated by comparing the measured value to the expected amount of Complement Component 5a (C5a) in samples.
| Matrix | Recovery range (%) | Average(%) |
| serum(n=5) | 85-98 | 92 |
| EDTA plasma(n=5) | 86-93 | 89 |
| heparin plasma(n=5) | 78-93 | 83 |
Precision of the CLIA Kit for Complement Component 5a (C5a)
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Complement Component 5a (C5a) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Complement Component 5a (C5a) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%
Linearity of the CLIA Kit for Complement Component 5a (C5a)
The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Complement Component 5a (C5a) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.
| Sample | 1:2 | 1:4 | 1:8 | 1:16 |
| serum(n=5) | 91-98% | 99-105% | 87-102% | 88-96% |
| EDTA plasma(n=5) | 83-102% | 95-102% | 94-101% | 92-101% |
| heparin plasma(n=5) | 90-98% | 78-95% | 81-104% | 94-105% |
Stability of the CLIA Kit for Complement Component 5a (C5a)
The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Assay procedure summary of the CLIA Kit for Complement Component 5a (C5a)
1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.
Test principle of the CLIA Kit for Complement Component 5a (C5a)
The microplate provided in this kit has been pre-coated with an antibody specific to Complement Component 5a (C5a). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Complement Component 5a (C5a). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Complement Component 5a (C5a) level in the sample or standard.;