CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3)

NIP3

  • CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) Packages (Simulation)
  • CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) Packages (Simulation)
  • CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) Results demonstration
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3)

This assay has high sensitivity and excellent specificity for detection of Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3).
No significant cross-reactivity or interference between Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) and analogues was observed.

Precision of the CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3)

The microplate provided in this kit has been pre-coated with an antibody specific to Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) level in the sample or standard.;

Related products

Catalog No. Organism species: Rattus norvegicus (Rat) Applications (RESEARCH USE ONLY!)
URPJ545Ra01 Recombinant Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) Positive Control; Immunogen; SDS-PAGE; WB.
UPAJ545Ra01 Polyclonal Antibody to Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) WB
UMAJ545Ra21 Monoclonal Antibody to Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) WB; IHC; ICC; IP.
USEJ545Ra ELISA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) Enzyme-linked immunosorbent assay for Antigen Detection.
USCJ545Ra CLIA Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) Chemiluminescent immunoassay for Antigen Detection.
ULMJ545Ra Multiplex Assay Kit for Bcl2/Adenovirus E1B 19kDa Interacting Protein 3 (BNIP3) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK