CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9)

MCMP; MDC9; Mltng; Meltrin Gamma; Metalloprotease/disintegrin/cysteine-rich protein 9; Myeloma cell metalloproteinase; Cellular disintegrin-related protein

  • CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9) Packages (Simulation)
  • CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9) Packages (Simulation)
  • CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9) Results demonstration
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9)

This assay has high sensitivity and excellent specificity for detection of A Disintegrin And Metalloprotease 9 (ADAM9).
No significant cross-reactivity or interference between A Disintegrin And Metalloprotease 9 (ADAM9) and analogues was observed.

Precision of the CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level A Disintegrin And Metalloprotease 9 (ADAM9) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level A Disintegrin And Metalloprotease 9 (ADAM9) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9)

The microplate provided in this kit has been pre-coated with an antibody specific to A Disintegrin And Metalloprotease 9 (ADAM9). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to A Disintegrin And Metalloprotease 9 (ADAM9). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the A Disintegrin And Metalloprotease 9 (ADAM9) level in the sample or standard.;

Related products

Catalog No. Organism species: Rattus norvegicus (Rat) Applications (RESEARCH USE ONLY!)
RPB829Ra01 Recombinant A Disintegrin And Metalloprotease 9 (ADAM9) Positive Control; Immunogen; SDS-PAGE; WB.
PAB829Ra01 Polyclonal Antibody to A Disintegrin And Metalloprotease 9 (ADAM9) WB; IHC; ICC; IP.
MAB829Ra21 Monoclonal Antibody to A Disintegrin And Metalloprotease 9 (ADAM9) WB; IHC; ICC; IP.
SEB829Ra ELISA Kit for A Disintegrin And Metalloprotease 9 (ADAM9) Enzyme-linked immunosorbent assay for Antigen Detection.
SCB829Ra CLIA Kit for A Disintegrin And Metalloprotease 9 (ADAM9) Chemiluminescent immunoassay for Antigen Detection.
LMB829Ra Multiplex Assay Kit for A Disintegrin And Metalloprotease 9 (ADAM9) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK