CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A)

RAB5

  • CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A) Packages (Simulation)
  • CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A) Packages (Simulation)
  • CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A) Results demonstration
  • SCK305Hu.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A)

This assay has high sensitivity and excellent specificity for detection of RAB5A, Member RAS Oncogene Family (RAB5A).
No significant cross-reactivity or interference between RAB5A, Member RAS Oncogene Family (RAB5A) and analogues was observed.

Precision of the CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level RAB5A, Member RAS Oncogene Family (RAB5A) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level RAB5A, Member RAS Oncogene Family (RAB5A) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A)

The microplate provided in this kit has been pre-coated with an antibody specific to RAB5A, Member RAS Oncogene Family (RAB5A). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to RAB5A, Member RAS Oncogene Family (RAB5A). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the RAB5A, Member RAS Oncogene Family (RAB5A) level in the sample or standard.;

Related products

Catalog No. Organism species: Homo sapiens (Human) Applications (RESEARCH USE ONLY!)
URPK305Hu01 Recombinant RAB5A, Member RAS Oncogene Family (RAB5A) Positive Control; Immunogen; SDS-PAGE; WB.
UPAK305Hu01 Polyclonal Antibody to RAB5A, Member RAS Oncogene Family (RAB5A) WB; IHC
UMAK305Hu21 Monoclonal Antibody to RAB5A, Member RAS Oncogene Family (RAB5A) WB; IHC
USEK305Hu ELISA Kit for RAB5A, Member RAS Oncogene Family (RAB5A) Enzyme-linked immunosorbent assay for Antigen Detection.
USCK305Hu CLIA Kit for RAB5A, Member RAS Oncogene Family (RAB5A) Chemiluminescent immunoassay for Antigen Detection.
ULMK305Hu Multiplex Assay Kit for RAB5A, Member RAS Oncogene Family (RAB5A) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK