ELISA Kit for Ferritin (FE)

  • ELISA Kit for Ferritin (FE) Packages (Simulation)
  • ELISA Kit for Ferritin (FE) Packages (Simulation)
  • ELISA Kit for Ferritin (FE) Results demonstration
  • SEA518Ga.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the ELISA Kit for Ferritin (FE)

This assay has high sensitivity and excellent specificity for detection of Ferritin (FE).
No significant cross-reactivity or interference between Ferritin (FE) and analogues was observed.

Recovery of the ELISA Kit for Ferritin (FE)

Matrices listed below were spiked with certain level of recombinant Ferritin (FE) and the recovery rates were calculated by comparing the measured value to the expected amount of Ferritin (FE) in samples.

Matrix Recovery range (%) Average(%)
serum(n=5) 80-97 94
EDTA plasma(n=5) 97-104 101
heparin plasma(n=5) 92-101 95

Precision of the ELISA Kit for Ferritin (FE)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Ferritin (FE) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Ferritin (FE) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Linearity of the ELISA Kit for Ferritin (FE)

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Ferritin (FE) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
serum(n=5) 88-99% 81-95% 95-105% 91-99%
EDTA plasma(n=5) 98-105% 85-93% 80-105% 81-101%
heparin plasma(n=5) 80-101% 85-99% 86-101% 94-101%

Stability of the ELISA Kit for Ferritin (FE)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the ELISA Kit for Ferritin (FE)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
8. Add 50µL Stop Solution. Read at 450nm immediately.

Test principle of the ELISA Kit for Ferritin (FE)

The test principle applied in this kit is Sandwich enzyme immunoassay. The microtiter plate provided in this kit has been pre-coated with an antibody specific to Ferritin (FE). Standards or samples are then added to the appropriate microtiter plate wells with a biotin-conjugated antibody specific to Ferritin (FE). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. After TMB substrate solution is added, only those wells that contain Ferritin (FE), biotin-conjugated antibody and enzyme-conjugated Avidin will exhibit a change in color. The enzyme-substrate reaction is terminated by the addition of sulphuric acid solution and the color change is measured spectrophotometrically at a wavelength of 450nm ± 10nm. The concentration of Ferritin (FE) in the samples is then determined by comparing the O.D. of the samples to the standard curve.

Related products

Catalog No. Organism species: Chicken (Gallus) Applications (RESEARCH USE ONLY!)
SEA518Ga ELISA Kit for Ferritin (FE) Enzyme-linked immunosorbent assay for Antigen Detection.
LMA518Ga Multiplex Assay Kit for Ferritin (FE) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK