ELISA Kit for Butyric Acid (BA)

Propanecarboxylic Acid; Butanoic Acid

  • ELISA Kit for Butyric Acid (BA) Packages (Simulation)
  • ELISA Kit for Butyric Acid (BA) Packages (Simulation)
  • ELISA Kit for Butyric Acid (BA) Results demonstration
  • CEO777Ge.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the ELISA Kit for Butyric Acid (BA)

This assay has high sensitivity and excellent specificity for detection of Butyric Acid (BA).
No significant cross-reactivity or interference between Butyric Acid (BA) and analogues was observed.

Precision of the ELISA Kit for Butyric Acid (BA)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Butyric Acid (BA) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Butyric Acid (BA) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the ELISA Kit for Butyric Acid (BA)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the ELISA Kit for Butyric Acid (BA)

1. Prepare all reagents, samples and standards;
2. Add 50µL standard or sample to each well.
    And then add 50µL prepared Detection Reagent A immediately.
    Shake and mix. Incubate 1 hour at 37°C;
3. Aspirate and wash 3 times;
4. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
5. Aspirate and wash 5 times;
6. Add 90µL Substrate Solution. Incubate 10-20 minutes at 37°C;
7. Add 50µL Stop Solution. Read at 450 nm immediately.

Test principle of the ELISA Kit for Butyric Acid (BA)

This assay employs the competitive inhibition enzyme immunoassay technique. A monoclonal antibody specific to Butyric Acid (BA) has been pre-coated onto a microplate. A competitive inhibition reaction is launched between biotin labeled Butyric Acid (BA) and unlabeled Butyric Acid (BA) (Standards or samples) with the pre-coated antibody specific to Butyric Acid (BA). After incubation the unbound conjugate is washed off. Next, avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. The amount of bound HRP conjugate is reverse proportional to the concentration of Butyric Acid (BA) in the sample. After addition of the substrate solution, the intensity of color developed is reverse proportional to the concentration of Butyric Acid (BA) in the sample.

Related products

Catalog No. Organism species: Pan-species (General) Applications (RESEARCH USE ONLY!)
CEO777Ge ELISA Kit for Butyric Acid (BA) Enzyme-linked immunosorbent assay for Antigen Detection.
LMO777Ge Multiplex Assay Kit for Butyric Acid (BA) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK