CLIA Kit for Reelin (RELN)

RL

  • CLIA Kit for Reelin (RELN) Packages (Simulation)
  • CLIA Kit for Reelin (RELN) Packages (Simulation)
  • CLIA Kit for Reelin (RELN) Results demonstration
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Reelin (RELN)

This assay has high sensitivity and excellent specificity for detection of Reelin (RELN).
No significant cross-reactivity or interference between Reelin (RELN) and analogues was observed.

Recovery of the CLIA Kit for Reelin (RELN)

Matrices listed below were spiked with certain level of recombinant Reelin (RELN) and the recovery rates were calculated by comparing the measured value to the expected amount of Reelin (RELN) in samples.

Matrix Recovery range (%) Average(%)
serum(n=5) 91-99 94
EDTA plasma(n=5) 86-93 90
heparin plasma(n=5) 83-102 90

Precision of the CLIA Kit for Reelin (RELN)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Reelin (RELN) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Reelin (RELN) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Linearity of the CLIA Kit for Reelin (RELN)

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Reelin (RELN) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
serum(n=5) 95-105% 80-99% 90-98% 93-102%
EDTA plasma(n=5) 86-93% 95-105% 79-103% 88-105%
heparin plasma(n=5) 99-105% 89-98% 91-103% 93-101%

Stability of the CLIA Kit for Reelin (RELN)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Reelin (RELN)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Reelin (RELN)

The microplate provided in this kit has been pre-coated with an antibody specific to Reelin (RELN). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Reelin (RELN). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Reelin (RELN) level in the sample or standard.;

Related products

Catalog No. Organism species: Rattus norvegicus (Rat) Applications (RESEARCH USE ONLY!)
RPC775Ra01 Recombinant Reelin (RELN) Positive Control; Immunogen; SDS-PAGE; WB.
PAC775Ra01 Polyclonal Antibody to Reelin (RELN) WB; IHC; ICC; IP.
LAC775Ra71 Biotin-Linked Polyclonal Antibody to Reelin (RELN) WB; IHC; ICC.
MAC775Ra21 Monoclonal Antibody to Reelin (RELN) WB; IHC; ICC; IP.
SEC775Ra ELISA Kit for Reelin (RELN) Enzyme-linked immunosorbent assay for Antigen Detection.
SCC775Ra CLIA Kit for Reelin (RELN) Chemiluminescent immunoassay for Antigen Detection.
LMC775Ra Multiplex Assay Kit for Reelin (RELN) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK