CLIA Kit for Prothrombin Fragment 1+2 (F1+2)
- Product No.SCA710Hu
- Organism SpeciesHomo sapiens (Human) Same name, Different species.
- Test MethodDouble-antibody Sandwich
- Assay Length2h, 40min
- Detection Range2.74-2,000pg/mL
- SensitivityThe minimum detectable dose of this kit is typically less than 1.03pg/mL.
- Sample TypeSerum, plasma, tissue homogenates, cell culture supernates and other biological fluids
- Download Instruction Manual
- UOM 48T96T 96T*5 96T*10 96T*100
-
FOB
US$ 588
For more details, please contact local distributors!US$ 840
For more details, please contact local distributors! US$ 3780
For more details, please contact local distributors! US$ 7140
For more details, please contact local distributors! US$ 58800
For more details, please contact local distributors!
-
Packages (Simulation)
-
Packages (Simulation)
-
Results demonstration
-
ISO9001: 2008, ISO13485: 2003 Registered
Specificity of the CLIA Kit for Prothrombin Fragment 1+2 (F1+2)
This assay has high sensitivity and excellent specificity for detection of Prothrombin Fragment 1+2 (F1+2).
No significant cross-reactivity or interference between Prothrombin Fragment 1+2 (F1+2) and analogues was observed.
Recovery of the CLIA Kit for Prothrombin Fragment 1+2 (F1+2)
Matrices listed below were spiked with certain level of recombinant Prothrombin Fragment 1+2 (F1+2) and the recovery rates were calculated by comparing the measured value to the expected amount of Prothrombin Fragment 1+2 (F1+2) in samples.
| Matrix | Recovery range (%) | Average(%) |
| serum(n=5) | 78-102 | 85 |
| EDTA plasma(n=5) | 84-101 | 90 |
| heparin plasma(n=5) | 85-92 | 89 |
Precision of the CLIA Kit for Prothrombin Fragment 1+2 (F1+2)
Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Prothrombin Fragment 1+2 (F1+2) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Prothrombin Fragment 1+2 (F1+2) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%
Linearity of the CLIA Kit for Prothrombin Fragment 1+2 (F1+2)
The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Prothrombin Fragment 1+2 (F1+2) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.
| Sample | 1:2 | 1:4 | 1:8 | 1:16 |
| serum(n=5) | 81-101% | 90-98% | 86-95% | 88-101% |
| EDTA plasma(n=5) | 98-105% | 94-102% | 96-105% | 95-103% |
| heparin plasma(n=5) | 92-101% | 78-97% | 85-92% | 78-89% |
Stability of the CLIA Kit for Prothrombin Fragment 1+2 (F1+2)
The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.
Assay procedure summary of the CLIA Kit for Prothrombin Fragment 1+2 (F1+2)
1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.
Test principle of the CLIA Kit for Prothrombin Fragment 1+2 (F1+2)
The microplate provided in this kit has been pre-coated with an antibody specific to Prothrombin Fragment 1+2 (F1+2). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Prothrombin Fragment 1+2 (F1+2). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Prothrombin Fragment 1+2 (F1+2) level in the sample or standard.;