CLIA Kit for Perilipin 4 (PLIN4)

Adipocyte protein S3-12

  • CLIA Kit for Perilipin 4 (PLIN4) Packages (Simulation)
  • CLIA Kit for Perilipin 4 (PLIN4) Packages (Simulation)
  • CLIA Kit for Perilipin 4 (PLIN4) Results demonstration
  • SCE040Mu.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Perilipin 4 (PLIN4)

This assay has high sensitivity and excellent specificity for detection of Perilipin 4 (PLIN4).
No significant cross-reactivity or interference between Perilipin 4 (PLIN4) and analogues was observed.

Precision of the CLIA Kit for Perilipin 4 (PLIN4)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Perilipin 4 (PLIN4) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Perilipin 4 (PLIN4) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for Perilipin 4 (PLIN4)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Perilipin 4 (PLIN4)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Perilipin 4 (PLIN4)

The microplate provided in this kit has been pre-coated with an antibody specific to Perilipin 4 (PLIN4). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Perilipin 4 (PLIN4). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Perilipin 4 (PLIN4) level in the sample or standard.;

Related products

Catalog No. Organism species: Mus musculus (Mouse) Applications (RESEARCH USE ONLY!)
RPE040Mu02 Recombinant Perilipin 4 (PLIN4) Positive Control; Immunogen; SDS-PAGE; WB.
RPE040Mu01 Recombinant Perilipin 4 (PLIN4) Positive Control; Immunogen; SDS-PAGE; WB.
PAE040Mu01 Polyclonal Antibody to Perilipin 4 (PLIN4) WB; IHC; ICC; IP.
PAE040Mu02 Polyclonal Antibody to Perilipin 4 (PLIN4) WB; IHC; ICC; IP.
SEE040Mu ELISA Kit for Perilipin 4 (PLIN4) Enzyme-linked immunosorbent assay for Antigen Detection.
SCE040Mu CLIA Kit for Perilipin 4 (PLIN4) Chemiluminescent immunoassay for Antigen Detection.
LME040Mu Multiplex Assay Kit for Perilipin 4 (PLIN4) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK