CLIA Kit for Filaggrin (FLG)

Profilaggrin

  • CLIA Kit for Filaggrin (FLG) Packages (Simulation)
  • CLIA Kit for Filaggrin (FLG) Packages (Simulation)
  • CLIA Kit for Filaggrin (FLG) Results demonstration
  • SCJ103Hu.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Filaggrin (FLG)

This assay has high sensitivity and excellent specificity for detection of Filaggrin (FLG).
No significant cross-reactivity or interference between Filaggrin (FLG) and analogues was observed.

Precision of the CLIA Kit for Filaggrin (FLG)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Filaggrin (FLG) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Filaggrin (FLG) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for Filaggrin (FLG)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Filaggrin (FLG)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Filaggrin (FLG)

The microplate provided in this kit has been pre-coated with an antibody specific to Filaggrin (FLG). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Filaggrin (FLG). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Filaggrin (FLG) level in the sample or standard.;

Related products

Catalog No. Organism species: Homo sapiens (Human) Applications (RESEARCH USE ONLY!)
RPJ103Hu02 Recombinant Filaggrin (FLG) Positive Control; Immunogen; SDS-PAGE; WB.
RPJ103Hu01 Recombinant Filaggrin (FLG) Positive Control; Immunogen; SDS-PAGE; WB.
RPJ103Hu03 Recombinant Filaggrin (FLG) Positive Control; Immunogen; SDS-PAGE; WB.
RPJ103Hu04 Recombinant Filaggrin (FLG) Positive Control; Immunogen; SDS-PAGE; WB.
PAJ103Hu01 Polyclonal Antibody to Filaggrin (FLG) WB; IHC; ICC; IP.
PAJ103Hu02 Polyclonal Antibody to Filaggrin (FLG) WB; IHC; ICC; IP.
LAJ103Hu71 Biotin-Linked Polyclonal Antibody to Filaggrin (FLG) WB; IHC; ICC.
LAJ103Hu81 FITC-Linked Polyclonal Antibody to Filaggrin (FLG) WB; IHC; ICC; IF.
MAJ103Hu21 Monoclonal Antibody to Filaggrin (FLG) WB; IHC; ICC; IP.
SEJ103Hu ELISA Kit for Filaggrin (FLG) Enzyme-linked immunosorbent assay for Antigen Detection.
SCJ103Hu CLIA Kit for Filaggrin (FLG) Chemiluminescent immunoassay for Antigen Detection.
LMJ103Hu Multiplex Assay Kit for Filaggrin (FLG) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK