CLIA Kit for Fibrillin 1 (FBN1)

FBN; MASS; MFS1; OCTD; SGS

  • CLIA Kit for Fibrillin 1 (FBN1) Packages (Simulation)
  • CLIA Kit for Fibrillin 1 (FBN1) Packages (Simulation)
  • CLIA Kit for Fibrillin 1 (FBN1) Results demonstration
  • SCA593Hu.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Fibrillin 1 (FBN1)

This assay has high sensitivity and excellent specificity for detection of Fibrillin 1 (FBN1).
No significant cross-reactivity or interference between Fibrillin 1 (FBN1) and analogues was observed.

Recovery of the CLIA Kit for Fibrillin 1 (FBN1)

Matrices listed below were spiked with certain level of recombinant Fibrillin 1 (FBN1) and the recovery rates were calculated by comparing the measured value to the expected amount of Fibrillin 1 (FBN1) in samples.

Matrix Recovery range (%) Average(%)
serum(n=5) 97-105 101
EDTA plasma(n=5) 95-104 98
heparin plasma(n=5) 83-98 89

Precision of the CLIA Kit for Fibrillin 1 (FBN1)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Fibrillin 1 (FBN1) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Fibrillin 1 (FBN1) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Linearity of the CLIA Kit for Fibrillin 1 (FBN1)

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of Fibrillin 1 (FBN1) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
serum(n=5) 78-89% 84-98% 89-96% 95-103%
EDTA plasma(n=5) 88-96% 92-101% 88-103% 91-99%
heparin plasma(n=5) 80-102% 78-102% 97-104% 80-96%

Stability of the CLIA Kit for Fibrillin 1 (FBN1)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Fibrillin 1 (FBN1)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Fibrillin 1 (FBN1)

The microplate provided in this kit has been pre-coated with an antibody specific to Fibrillin 1 (FBN1). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Fibrillin 1 (FBN1). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Fibrillin 1 (FBN1) level in the sample or standard.;

Related products

Catalog No. Organism species: Homo sapiens (Human) Applications (RESEARCH USE ONLY!)
RPA593Hu01 Recombinant Fibrillin 1 (FBN1) Positive Control; Immunogen; SDS-PAGE; WB.
RPA593Hu07 Recombinant Fibrillin 1 (FBN1) Positive Control; Immunogen; SDS-PAGE; WB.
RPA593Hu06 Recombinant Fibrillin 1 (FBN1) Positive Control; Immunogen; SDS-PAGE; WB.
RPA593Hu02 Recombinant Fibrillin 1 (FBN1) Positive Control; Immunogen; SDS-PAGE; WB.
RPA593Hu05 Recombinant Fibrillin 1 (FBN1) Positive Control; Immunogen; SDS-PAGE; WB.
RPA593Hu03 Recombinant Fibrillin 1 (FBN1) Positive Control; Immunogen; SDS-PAGE; WB.
RPA593Hu04 Recombinant Fibrillin 1 (FBN1) Positive Control; Immunogen; SDS-PAGE; WB.
PAA593Hu02 Polyclonal Antibody to Fibrillin 1 (FBN1) WB; ICC; IHC-P; IHC-F; ELISA.
PAA593Hu01 Polyclonal Antibody to Fibrillin 1 (FBN1) WB; IHC; ICC; IP.
PAA593Hu03 Polyclonal Antibody to Fibrillin 1 (FBN1) WB; ICC; IHC-P; IHC-F; ELISA.
PAA593Hu04 Polyclonal Antibody to Fibrillin 1 (FBN1) WB; ICC; IHC-P; IHC-F; ELISA.
PAA593Hu05 Polyclonal Antibody to Fibrillin 1 (FBN1) WB; IHC; ICC; IP.
PAA593Hu06 Polyclonal Antibody to Fibrillin 1 (FBN1) WB; IHC; ICC; IP.
LAA593Hu81 FITC-Linked Polyclonal Antibody to Fibrillin 1 (FBN1) WB; IHC; ICC; IF.
LAA593Hu71 Biotin-Linked Polyclonal Antibody to Fibrillin 1 (FBN1) WB; IHC; ICC.
MAA593Hu22 Monoclonal Antibody to Fibrillin 1 (FBN1) WB; IHC; ICC; IP.
SEA593Hu ELISA Kit for Fibrillin 1 (FBN1) Enzyme-linked immunosorbent assay for Antigen Detection.
SCA593Hu CLIA Kit for Fibrillin 1 (FBN1) Chemiluminescent immunoassay for Antigen Detection.
LMA593Hu Multiplex Assay Kit for Fibrillin 1 (FBN1) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
KSA593Hu01 ELISA Kit DIY Materials for Fibrillin 1 (FBN1) Main materials for "Do It(ELISA Kit) Yourself"
GUESTBOOK