CLIA Kit for Ferroportin (FPN)

SLC40A1; FPN1; HFE4; IREG1; MTP1; SLC11A3; Solute Carrier Family 40,Member 1; Iron-Regulated Transporter

  • CLIA Kit for Ferroportin (FPN) Packages (Simulation)
  • CLIA Kit for Ferroportin (FPN) Packages (Simulation)
  • CLIA Kit for Ferroportin (FPN) Results demonstration
  • SCC489Mu.jpg Typical Standard Curve
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for Ferroportin (FPN)

This assay has high sensitivity and excellent specificity for detection of Ferroportin (FPN).
No significant cross-reactivity or interference between Ferroportin (FPN) and analogues was observed.

Precision of the CLIA Kit for Ferroportin (FPN)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level Ferroportin (FPN) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level Ferroportin (FPN) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Stability of the CLIA Kit for Ferroportin (FPN)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for Ferroportin (FPN)

1. Prepare all reagents, samples and standards;
2. Add 100µL standard or sample to each well. Incubate 1 hours at 37°C;
3. Aspirate and add 100µL prepared Detection Reagent A. Incubate 1 hour at 37°C;
4. Aspirate and wash 3 times;
5. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
6. Aspirate and wash 5 times;
7. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
8. Read RLU value immediately.

Test principle of the CLIA Kit for Ferroportin (FPN)

The microplate provided in this kit has been pre-coated with an antibody specific to Ferroportin (FPN). Standards or samples are then added to the appropriate microplate wells with a biotin-conjugated antibody specific to Ferroportin (FPN). Next, Avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is proportional to the Ferroportin (FPN) level in the sample or standard.;

Related products

Catalog No. Organism species: Mus musculus (Mouse) Applications (RESEARCH USE ONLY!)
RPC489Mu02 Recombinant Ferroportin (FPN) Positive Control; Immunogen; SDS-PAGE; WB.
RPC489Mu01 Recombinant Ferroportin (FPN) Positive Control; Immunogen; SDS-PAGE; WB.
CPC489Mu21 OVA Conjugated Ferroportin (FPN) Immunogen; SDS-PAGE; WB.
PAC489Mu02 Polyclonal Antibody to Ferroportin (FPN) WB; IHC; ICC; IP.
PAC489Mu01 Polyclonal Antibody to Ferroportin (FPN) WB; IHC; ICC; IP.
SEC489Mu ELISA Kit for Ferroportin (FPN) Enzyme-linked immunosorbent assay for Antigen Detection.
SCC489Mu CLIA Kit for Ferroportin (FPN) Chemiluminescent immunoassay for Antigen Detection.
LMC489Mu Multiplex Assay Kit for Ferroportin (FPN) ,etc. by FLIA (Flow Luminescence Immunoassay) FLIA Kit for Antigen Detection.
GUESTBOOK