CLIA Kit for D-Dimer (D2D)

D 2 Dimer

  • CLIA Kit for D-Dimer (D2D) Packages (Simulation)
  • CLIA Kit for D-Dimer (D2D) Packages (Simulation)
  • CLIA Kit for D-Dimer (D2D) Results demonstration
  • Certificate ISO9001: 2008, ISO13485: 2003 Registered

Specificity of the CLIA Kit for D-Dimer (D2D)

This assay has high sensitivity and excellent specificity for detection of D-Dimer (D2D).
No significant cross-reactivity or interference between D-Dimer (D2D) and analogues was observed.

Recovery of the CLIA Kit for D-Dimer (D2D)

Matrices listed below were spiked with certain level of recombinant D-Dimer (D2D) and the recovery rates were calculated by comparing the measured value to the expected amount of D-Dimer (D2D) in samples.

Matrix Recovery range (%) Average(%)
sodium citrate plasma(n=5) 83-92 87

Precision of the CLIA Kit for D-Dimer (D2D)

Intra-assay Precision (Precision within an assay): 3 samples with low, middle and high level D-Dimer (D2D) were tested 20 times on one plate, respectively.
Inter-assay Precision (Precision between assays): 3 samples with low, middle and high level D-Dimer (D2D) were tested on 3 different plates, 8 replicates in each plate.
CV(%) = SD/meanX100
Intra-Assay: CV<10%
Inter-Assay: CV<12%

Linearity of the CLIA Kit for D-Dimer (D2D)

The linearity of the kit was assayed by testing samples spiked with appropriate concentration of D-Dimer (D2D) and their serial dilutions. The results were demonstrated by the percentage of calculated concentration to the expected.

Sample 1:2 1:4 1:8 1:16
sodium citrate plasma(n=5) 96-105% 85-96% 81-98% 89-99%

Stability of the CLIA Kit for D-Dimer (D2D)

The stability of kit is determined by the loss rate of activity. The loss rate of this kit is less than 5% within the expiration date under appropriate storage condition.
To minimize extra influence on the performance, operation procedures and lab conditions, especially room temperature, air humidity, incubator temperature should be strictly controlled. It is also strongly suggested that the whole assay is performed by the same operator from the beginning to the end.

Assay procedure summary of the CLIA Kit for D-Dimer (D2D)

1. Prepare all reagents, samples and standards;
2. Add 50µL standard or sample to each well.
    And then add 50µL prepared Detection Reagent A immediately.
    Shake and mix. Incubate 1 hour at 37°C;
3. Aspirate and wash 3 times;
4. Add 100µL prepared Detection Reagent B. Incubate 30 minutes at 37°C;
5. Aspirate and wash 5 times;
6. Add 100µL Substrate Solution. Incubate 10 minutes at 37°C;
7. Read RLU value immediately.

Test principle of the CLIA Kit for D-Dimer (D2D)

The microplate provided in this kit has been pre-coated with a monoclonal antibody specific to D-Dimer (D2D). A competitive inhibition reaction is launched between biotin labeled D-Dimer (D2D) and unlabeled D-Dimer (D2D) (Standards or samples) with the pre-coated antibody specific to D-Dimer (D2D). After incubation the unbound conjugate is washed off. Next, avidin conjugated to Horseradish Peroxidase (HRP) is added to each microplate well and incubated. The amount of bound HRP conjugate is reverse proportional to the concentration of D-Dimer (D2D) in the sample. Then the mixture of substrate A and B is added to generate glow light emission kinetics. Upon plate development, the intensity of the emitted light is reverse proportional to the D-Dimer (D2D) level in the sample or standard.

Related products

Catalog No. Organism species: Mus musculus (Mouse) Applications (RESEARCH USE ONLY!)
CEA506Mu ELISA Kit for D-Dimer (D2D) Enzyme-linked immunosorbent assay for Antigen Detection.
WEA506Mu Wide-range ELISA Kit for D-Dimer (D2D) Enzyme-linked immunosorbent assay for Antigen Detection.
CCA506Mu CLIA Kit for D-Dimer (D2D) Chemiluminescent immunoassay for Antigen Detection.
KSA506Mu11 ELISA Kit DIY Materials for D-Dimer (D2D) Main materials for "Do It (ELISA Kit) Yourself".
GUESTBOOK